When you first start using a Ring Doorbell, it might be difficult to comprehend the many indications that it sends out. When my Ring Doorbell began glowing blue, like everyone else, I was completely baffled. On the other hand, as a result of my prior expertise with the upkeep and installation of Ring Doorbells, I can guarantee you that the flashing blue light has a simple cause and can be rectified with little effort.
When the blue light on your Ring Doorbell flashes, it notifies you of a certain condition or status. In order to determine what the problem is, you may attempt to set off various alarms or other events that would typically cause the doorbell to ring. You may, for instance, test the doorbell’s response by ringing it or by moving anything in front of it to check whether it works properly.
It is essential that you evaluate the functioning of the internet connection in addition to evaluating the doorbell’s performance. In order for the Ring Doorbell to perform its functions correctly, a constant and dependable internet connection is required. Check that the strength of your Wi-Fi signal is sufficient and that there are no problems with the connection to your router.
You’ll be able to determine why the blue light on your Ring Doorbell is blinking if you follow these straightforward troubleshooting procedures, and then you’ll be able to address the problem in a timely manner. The Ring Doorbell continues to be one of the most impressive smart doorbells that can be purchased today due to the fact that it can be set up quickly and easily, it streams video and audio of a high quality, and it is compatible with home automation systems.
Why Is My Ring Doorbell Flashing Blue?
| Light Pattern | Meaning |
|---|---|
| Spinning Blue | Normal doorbell push notification |
| Solid Blue | Call answered or connected to the Ring Doorbell |
| Upward Moving Blue | Ring Doorbell trying to connect to Wi-Fi network |
| Flashing Blue (1 sec on, 1 sec off) | Ring Doorbell restarting or stuck in boot loop |
| 4 Blue LEDs flashing four times | Ring Doorbell set up successfully |
| Rapid Blue flash, then White | Factory reset on Ring Doorbell completed |
| Top Half Flashing Blue | During setup: “bad password” / After setup: Charging |
There are a few different troubleshooting procedures that you may do if the blue light on your Ring Doorbell is blinking. To begin, you should initiate the alarms or events that should activate the doorbell. For example, you may ring the doorbell or create motion in front of it. In addition, verify your internet connection to confirm that it is steady and operating correctly. It is suggested that you get in touch with Ring support for further help if the problem with the flashing blue light continues even after trying these troubleshooting procedures.
The status and fault signals for your Ring Doorbell will be shown in the form of a round, circular light on the front of the device. These signals may be interpreted in a variety of ways, depending on whether the light is steady or flickering, the frequency at which it blinks, and which part of the circle is illuminated. You will be better equipped to deal with any difficulties that emerge with your Ring Doorbell if you have a working knowledge of the various messages and the light patterns that correlate to them.
If the blue light is flashing
When you press the button on your Ring Doorbell and a blue light begins to revolve, this signifies a standard push notification. This happens rather often, and there is no need to be alarmed about it.
If the light is all blue
A call that has been answered or that you are connected to your Ring Doorbell is shown by a solid blue light on the device. It shows that the doorbell speaker is on and that someone is listening in on the call.
If the light is a blue, travelling upward
If the blue light on your Ring Doorbell is rising higher, this indicates that the device is trying to connect to your Wi-Fi network. This occurs often during the process of setting up a device, but it may also be an indication of a problem with the Wi-Fi connection at other times, such as when your internet is unavailable because of a power outage or a storm.
Blue flashing lights should be 1 second on, 1 second off.
A blue light that blinks on and off in a sequence of one second on and one second off indicates that the Ring Doorbell is either restarting itself or becoming trapped in a boot loop. If the flashing continues for a lengthy period of time, it is strongly recommended that you get in touch with support to get help.
If a lamp contains four blue LEDs that flash once per four cycles
When the light on your Ring Doorbell consists of four blue LEDs that flash four times, this indicates that the doorbell has been successfully set up. In the event that this does place, there is absolutely no need for alarm.
If the lights quickly flash blue before becoming white
It is a sign that you have successfully accomplished a factory reset on your Ring Doorbell if the lights begin to quickly flash blue and then turn white once the reset is finished.
If the blue flashing top half
There are two possible interpretations for the situation in which the blue flashing light is just on the upper part of the signal. The error message “bad password” appears when you are going through the setup procedure. Following the installation, this indicator shows that the Ring Doorbell is currently linked to a power source and charging.
Blue Light Flashing when setting up Ring Doorbell
During the initial setup of your Ring Doorbell, the LED light will rotate instead of flashing continuously. As the process of setting up advances, the LED light will change into a pattern that flashes blue and goes in an upward direction. This suggests that your doorbell is making preparations to link up with your home’s Wi-Fi network at the present time.
During the setup process for the Ring app, if you make the mistake of entering the incorrect password, the top half of the blue light will blink. In order for you to successfully finish the setup procedure, you will be prompted to re-enter the password and ensure that it is entered properly.
When the installation of your Ring Doorbell has been successfully completed, the LED light on the device will flash blue four times, and then it will show a white circle. This means that your doorbell is prepared for usage and is ready to be utilised.
In order for your Ring Doorbell to work correctly, it is essential to ensure that you have a reliable and robust Wi-Fi connection at all times. It is possible that you may have delays or problems with the operation of your doorbell if you do not have a stable Wi-Fi connection.
Ring Doorbell Flashing Blue Light Randomly
When the setup is complete and your Ring Doorbell begins to glow blue at one-second intervals, your doorbell is rebooting. This can take place if the doorbell experiences a power outage or an automatic firmware upgrade. In these situations, all you have to do is wait for the doorbell to reset, which might take a few minutes. Ring Doorbells often need reboots, which is typical. However, if the frequent reboots continue on a regular basis, it may be a sign of something more serious.
Make sure to frequently charge your doorbell to avoid repeated reboots. Make sure the cables are secure and undamaged for hardwired doorbells.
Depending on the model, the blue light’s behaviour while your Ring Doorbell is charging may change. The charging cable for first- and second-generation devices must be inserted into the port behind the doorbell in order to recharge the battery. When the doorbell is charging, a blue LED will blink, and the circle light will fill up as the battery life increases. The light will become solid blue when the battery is charged completely.
Removing the batteries from battery-operated Ring Doorbells with replaceable batteries will turn the light off; replacing the batteries will put the light back on.
Despite being hardwired, the Ring Doorbell Pro still has to be charged for a few hours after installation. During setup, charging starts automatically, and the top half of the LED light starts to flicker blue. When the doorbell has completed charging, the blinking will cease.
Even when the doorbell has just been charged, the Ring app’s battery assessment sometimes displays the doorbell as having low power. on these circumstances, a few doorbell rings will update the battery level on the app and provide a more precise readout.
You can keep your Ring Doorbell operating at its peak performance by according to these instructions and making sure it is charged properly.
Wrapping it up
Blinking patterns that the LED light on your Ring Doorbell displays convey critical information to you. By recognising these patterns, you will be better able to assess the current state of your equipment.
In most cases, there is no need for concern even if the blue light on your Ring Doorbell flashes continuously and in rapid succession. This problem may, in many instances, be rectified by following a few simple procedures. Charging the doorbell is a typical technique that may be used to guarantee that it has enough power. In addition to that, trying to fix the issue by conducting a reboot, which means restarting the device, may not be successful.
However, if the problem continues even after charging the device and restarting it, you should look for help from a professional. You may contact Ring’s customer care service for assistance and direction if you have any questions. You also have the option of going to a service centre in the area, where qualified technicians may examine and perhaps repair your doorbell for you.
By enlisting the assistance of a professional, you can be certain that any underlying problems with your Ring Doorbell will be thoroughly handled. This will enable you to restore the device’s functioning and continue using it in an efficient manner.
You Might Also Enjoy Reading: Ring Video Doorbell Flashing White Light! How to Fix It?